Browse our collection of stainless steel nuts, bolts and threaded rod. We also have a full collection of joist hangers, straps and connectors, perfect for building decks, docks and more.
Many Simpson Hangers are made in the USA. Same Day Shipping.
If you don't see what you need, contact us about putting in a special order! Get a quote
Made in the USA Coiled strap is a continuous utility strap. Built to resist tension and uplift. Nail slots provided for easy installation Continuous utility strap can be cut to length on the job site Type 316 Stainless Steel for ultimate corrosion resistance Install with specified stainless steel fasteners
$277.85
Ideal for sight exposed connections and end of ledger/rim joist installations Made in the USA Type 316 Stainless Steel for ultimate corrosion resistance Install with specified stainless steel fasteners Under certain conditions, alternative size nails or Simpson SD screws may be substituted. Note that it may significantly alter load capacity. See the nail substitution chart. Caution! - Do not bend or remove tabs or alter hanger in any way
$75.50
Ideal for sight exposed connections and end of ledger/rim joist installations Made in the USA Type 316 Stainless Steel for ultimate corrosion resistance Install with specified stainless steel fasteners Under certain conditions, alternative size nails or Simpson SD screws may be substituted. Note that it may significantly alter load capacity. See the nail substitution chart. Caution! - Do not bend or remove tabs or alter hanger in any way
$68.50
Type 410 Stainless Steel for enhanced corrosion protectionAvailable in Hex and Phillips Flat Head, 100pc BoxIdeal for attaching components like light fixtures or electrical boxes to concrete and masonryGreat for concrete, brick, grout-filled CMU and hollow-block applicationsSuitable for some preservative-treaded wood applicationsDrill Bits included in each box
$60.65 - $110.65
Made in the USA Straight straps are used to transfer tension loads in a wide variety of applications Type 316 Stainless Steel for ultimate corrosion resistance Install with specified stainless steel fasteners
$49.50
The SU series of hangers are skewed 45° left or right. Angled nail slots direct nails for proper placement. These hangers will normally accommodate a 40° - 50° skew. The letter "L" in the code designates left skew. The letter "R" designates right skew. Made in the USA Type 316 Stainless Steel for ultimate corrosion resistance Features several configurations for wind and seismic resistance ties for trusses and rafters. Install with specified stainless steel fasteners
$48.00
The SU series of hangers are skewed 45° left or right. Angled nail slots direct nails for proper placement. These hangers will normally accommodate a 40° - 50° skew. The letter "L" in the code designates left skew. The letter "R" designates right skew. Made in the USA Type 316 Stainless Steel for ultimate corrosion resistance Features several configurations for wind and seismic resistance ties for trusses and rafters. Install with specified stainless steel fasteners
$48.00
The SU series of hangers are skewed 45° left or right. Angled nail slots direct nails for proper placement. These hangers will normally accommodate a 40° - 50° skew. The letter "L" in the code designates left skew. The letter "R" designates right skew. Made in the USA Type 316 Stainless Steel for ultimate corrosion resistance Features several configurations for wind and seismic resistance ties for trusses and rafters. Install with specified stainless steel fasteners
$46.15
The SU series of hangers are skewed 45° left or right. Angled nail slots direct nails for proper placement. These hangers will normally accommodate a 40° - 50° skew. The letter "L" in the code designates left skew. The letter "R" designates right skew. Made in the USA Type 316 Stainless Steel for ultimate corrosion resistance Features several configurations for wind and seismic resistance ties for trusses and rafters. Install with specified stainless steel fasteners
$46.15
The SU series of hangers are skewed 45° left or right. Angled nail slots direct nails for proper placement. These hangers will normally accommodate a 40° - 50° skew. The letter "L" in the code designates left skew. The letter "R" designates right skew. Made in the USA Type 316 Stainless Steel for ultimate corrosion resistance Features several configurations for wind and seismic resistance ties for trusses and rafters. Install with specified stainless steel fasteners
$38.85
The SU series of hangers are skewed 45° left or right. Angled nail slots direct nails for proper placement. These hangers will normally accommodate a 40° - 50° skew. The letter "L" in the code designates left skew. The letter "R" designates right skew. Made in the USA Type 316 Stainless Steel for ultimate corrosion resistance Features several configurations for wind and seismic resistance ties for trusses and rafters. Install with specified stainless steel fasteners
$38.85
Ideal for sight exposed connections and end of ledger/rim joist installations Made in the USA Type 316 Stainless Steel for ultimate corrosion resistance Install with specified stainless steel fasteners Under certain conditions, alternative size nails or Simpson SD screws may be substituted. Note that it may significantly alter load capacity. See the nail substitution chart. Caution! - Do not bend or remove tabs or alter hanger in any way
$37.50
Ideal for sight exposed connections and end of ledger/rim joist installations Made in the USA Type 316 Stainless Steel for ultimate corrosion resistance Install with specified stainless steel fasteners Under certain conditions, alternative size nails or Simpson SD screws may be substituted. Note that it may significantly alter load capacity. See the nail substitution chart. Caution! - Do not bend or remove tabs or alter hanger in any way
$34.15
Made in the USA Twist straps provide tension connections between two wood members Type 316 Stainless Steel for ultimate corrosion resistance Install with specified stainless steel fasteners
$26.70
Made in the USA Reinforcing and adjustable angle Site bendable (one time) from 0° - 130° to fit your application. Used for joist framing where a standard hanger isn’t practical. Bending more than once will cause metal fatigue and severely reduced load capacity.
$25.65
Made in the USA with Type 316 (low Carbon) Stainless Steel 316 stainless provides the highest salt water corrosion resistance of the 316 types. Appropriate for marine and seaside applications and in other severe conditions where corrosion is a concern Must be installed with specified stainless steel fasteners Patented double shear nailing distributes the load through 2 points on each joist for greater strength. The nails slant through the joist into the header, not only fastening the hanger but also helping to carry some of the load. The hanger design allows for the use of fewer fasteners for faster installation Install with specified stainless steel fasteners Full length 3” or 3-1/2” hand drive nails (or 2-1/2” collated connector nails) are always required for the patented double sheer (angled) nailing. Under some conditions alternative sized fasteners may be substituted but at a potentially significant load reduction. See nail substitution chart. LUS series hangers are not intended for welded applications Caution! - Do not bend or remove tabs or alter hanger in any way
$24.30
Made in the USA Straight straps are used to transfer tension loads in a wide variety of applications Type 316 Stainless Steel for ultimate corrosion resistance Install with specified stainless steel fasteners
$23.20
Made in the USA with Type 316 (low Carbon) Stainless Steel 316 stainless provides the highest salt water corrosion resistance of the 316 types. Appropriate for marine and seaside applications and in other severe conditions where corrosion is a concern Must be installed with specified stainless steel fasteners Patented double shear nailing distributes the load through 2 points on each joist for greater strength. The nails slant through the joist into the header, not only fastening the hanger but also helping to carry some of the load. The hanger design allows for the use of fewer fasteners for faster installation Install with specified stainless steel fasteners Full length 3” or 3-1/2” hand drive nails (or 2-1/2” collated connector nails) are always required for the patented double sheer (angled) nailing. Under some conditions alternative sized fasteners may be substituted but at a potentially significant load reduction. See nail substitution chart. LUS series hangers are not intended for welded applications Caution! - Do not bend or remove tabs or alter hanger in any way
$20.55
Made in the USA Features several configurations for wind and seismic resistant ties for trusses and rafters Type 316 Stainless Steel for ultimate corrosion resistance Install with specified stainless steel fasteners
$19.85
Made in the USA with Type 316 (low Carbon) Stainless Steel 316 stainless provides the highest salt water corrosion resistance of the 316 types. Appropriate for marine and seaside applications and in other severe conditions where corrosion is a concern Must be installed with specified stainless steel fasteners Patented double shear nailing distributes the load through 2 points on each joist for greater strength. The nails slant through the joist into the header, not only fastening the hanger but also helping to carry some of the load. The hanger design allows for the use of fewer fasteners for faster installation Install with specified stainless steel fasteners Full length 3” or 3-1/2” hand drive nails (or 2-1/2” collated connector nails) are always required for the patented double sheer (angled) nailing. Under some conditions alternative sized fasteners may be substituted but at a potentially significant load reduction. See nail substitution chart. LUS series hangers are not intended for welded applications Caution! - Do not bend or remove tabs or alter hanger in any way
$19.25
Made in the USA Twist straps provide tension connections between two wood members Type 316 Stainless Steel for ultimate corrosion resistance Install with specified stainless steel fasteners
$19.00
Made in the USA with Type 316 (low Carbon) Stainless Steel 316 stainless provides the highest salt water corrosion resistance of the 316 types. Appropriate for marine and seaside applications and in other severe conditions where corrosion is a concern Must be installed with specified stainless steel fasteners Patented double shear nailing distributes the load through 2 points on each joist for greater strength. The nails slant through the joist into the header, not only fastening the hanger but also helping to carry some of the load. The hanger design allows for the use of fewer fasteners for faster installation Install with specified stainless steel fasteners Full length 3” or 3-1/2” hand drive nails (or 2-1/2” collated connector nails) are always required for the patented double sheer (angled) nailing. Under some conditions alternative sized fasteners may be substituted but at a potentially significant load reduction. See nail substitution chart. LUS series hangers are not intended for welded applications Caution! - Do not bend or remove tabs or alter hanger in any way
$17.40
Made in the USA with Type 316 (low Carbon) Stainless Steel 316 stainless provides the highest salt water corrosion resistance of the 316 types. Appropriate for marine and seaside applications and in other severe conditions where corrosion is a concern Must be installed with specified stainless steel fasteners Patented double shear nailing distributes the load through 2 points on each joist for greater strength. The nails slant through the joist into the header, not only fastening the hanger but also helping to carry some of the load. The hanger design allows for the use of fewer fasteners for faster installation Install with specified stainless steel fasteners Full length 3” or 3-1/2” hand drive nails (or 2-1/2” collated connector nails) are always required for the patented double sheer (angled) nailing. Under some conditions alternative sized fasteners may be substituted but at a potentially significant load reduction. See nail substitution chart. LUS series hangers are not intended for welded applications Caution! - Do not bend or remove tabs or alter hanger in any way
$15.37
Made in the USA Straight straps are used to transfer tension loads in a wide variety of applications Type 316 Stainless Steel for ultimate corrosion resistance Install with specified stainless steel fasteners
$14.80
Made in the USA Features several configurations for wind and seismic resistant ties for trusses and rafters Type 316 Stainless Steel for ultimate corrosion resistance Install with specified stainless steel fasteners Approved for installation with SD Connector Screws
$13.05
Made in the USA Twist straps provide tension connections between two wood members Type 316 Stainless Steel for ultimate corrosion resistance Install with specified stainless steel fasteners
$12.40
Made in the USA with Type 316 (low Carbon) Stainless Steel 316 stainless provides the highest salt water corrosion resistance of the 316 types. Appropriate for marine and seaside applications and in other severe conditions where corrosion is a concern Must be installed with specified stainless steel fasteners Patented double shear nailing distributes the load through 2 points on each joist for greater strength. The nails slant through the joist into the header, not only fastening the hanger but also helping to carry some of the load. The hanger design allows for the use of fewer fasteners for faster installation Install with specified stainless steel fasteners Full length 3” or 3-1/2” hand drive nails (or 2-1/2” collated connector nails) are always required for the patented double sheer (angled) nailing. Under some conditions alternative sized fasteners may be substituted but at a potentially significant load reduction. See nail substitution chart. LUS series hangers are not intended for welded applications Caution! - Do not bend or remove tabs or alter hanger in any way
$12.15
Made in the USA Twist straps provide tension connections between two wood members Type 316 Stainless Steel for ultimate corrosion resistance Install with specified stainless steel fasteners
$11.90
The WEDGE-ALL® wedge anchors are a non-bottom bearing, wedge style expansion anchor for use in solid concrete or grout filled masonry.One-piece, wrap-around clip ensures uniform holding capacityThreaded end is chamfered for ease of starting nutOne piece wrap around clipSupplied with a nut and washerThreaded end is chamfered for ease of starting nutThreaded studs are set by tightening the nut Discontinued product, limited quantities available
$11.15 - $66.95
Made in the USA Features several configurations for wind and seismic resistant ties for trusses and rafters Replaces the H2SS Type 316L Stainless Steel for ultimate corrosion resistance Install with specified stainless steel fasteners
$11.10
Made in the USA Straight straps are used to transfer tension loads in a wide variety of applications Type 316 Stainless Steel for ultimate corrosion resistance Install with specified stainless steel fasteners
$10.80
Made in the USA Features several configurations for wind and seismic resistant ties for trusses and rafters Sold in pairs, right and left Type 316 Stainless Steel for ultimate corrosion resistance Install with specified stainless steel fasteners
$8.95
Type 316 Stainless Steel for ultimate corrosion resistance Code listed for cracked concrete and uncracked concrete See code listings Head stamped with length identification number Chamfered top to prevent mushrooming during installation Optimal choice for performance under seismic and high-wind conditions Qualified for a minimum 3-1/4” concrete thickness Tested per ACI355.2 and AC193 specifications concrete design information available in spec section below
$7.37 - $14.30
The Titen HD® now with countersunk head style!This high-strength screw anchor is perfect for use in cracked and uncracked concrete as well as masonry. Conveniently sold by the piece! Type 316 Stainless Steel provides long-lasting corrosion resistance. Cracked concrete code listed Provides industry leading Countersunk head leaves a flush-mount profile and clean surface appearance for exposed through-set applications performance even in seismic and wind loading conditions Installs using a standard-sized ANSI tolerance drill bit - The 3/8" Titen takes a T-50 bit, sold separately here. Removable. Great for temporary anchoring See spec table for installation pdf
$5.30 - $7.25
Made in the USA Reversable and bendable one time to fit your application Features a speed prong to easily hold connector in place while fastening with nails Install with specified stainless steel fasteners
$5.15
This framing angle designed to be used in various connections. Made in the USA Features a speed prong to easily hold connector in place while fastening with nails or SD screws Install with specified stainless steel fasteners
$4.70
Made in the USA Features several configurations for wind and seismic resistant ties for trusses and rafters Replaces the H2.5SS Type 316 Stainless Steel for ultimate corrosion resistance Install with specified stainless steel fasteners
$4.58
18-8 & 316 Stainless Steel You may cut stainless steel threaded rod to the desired length with a diamond or carborundum blade Ideal for applications requiring a longer length bolt Be sure to use anti-seize compound or lubricant like WD-40 to prevent thread seizing. Approved for use in ACQ lumber 6 foot lengths are available in most diameters. *Depending on size, minimums may apply*Does not qualify for free shipping. Shipping details in additional information section below
$4.44 - $69.00
Type 18-8 & 316 Stainless Steel Choose from 4 diameters Hard to find long lengths Length is measured from under head to tip of screw Be sure to use anti-seize compound or lubricant like WD-40 to prevent thread seizing.
$4.25 - $19.30
Type 18-8 & 316 Stainless Steel Hard to find long lengths Length is measured from under head to tip of screw Threaded portion is variable depending on length of bolt Be sure to use anti-seize compound or lubricant like WD-40 to prevent thread seizing.
$4.20 - $9.90
Titen HD® is made from Type 316 Stainless Steel with carbon-steel lead-threads Perfect for concrete and masonry where corrosion is a concern. Serrated carbon-steel threads at the tip cut concrete and allow remaining threads to interlock with the concrete. Contains less than 1% carbon steel to minimize expansion compared to 18% found in other stainless screw anchors. Unlike other anchors, the Titen HD® will not cause concrete failure due to rust. See design info PDF in the specs section below. Install by hand or with an impact wrench. See PDF in spec section for installation information
$4.10 - $22.50
Type 18-8 & 316 Stainless Steel Hard to find long lengths Length is measured from under head to tip of screw Threaded portion is variable depending on length of bolt Be sure to use anti-seize compound or lubricant like WD-40 to prevent thread seizing.
$1.62 - $21.79
Type 18-8 & 316 Stainless Steel Choose from 4 diameters Hard to find long lengths Length is measured from under head to tip of screw
$0.84 - $26.88
Type 18-8 & 316 Stainless Steel Choose from 4 diameters Hard to find long lengths Length is measured from under head to tip of screw Be sure to use anti-seize compound or lubricant like WD-40 to prevent thread seizing.
$0.77 - $18.99
Type 18-8 and 316 Stainless Steel Sold by the pieceBuy more and save!
$0.73 - $39.32
Type 18-8 & 316 Stainless Steel Choose from 4 diameters Hard to find long lengths Length is measured from under head to tip of screw
$0.60 - $42.95
Stainless Steel T-Nuts (Tee Nuts) 3 or 4 prong - see chart for details Great for cabinetry and woodworking Nuts install flush with the wood surface Standard UNC coarse threads Sold by the piece, discounts when you buy 100 or more.
$0.41 - $2.59
Type 18-8 & 316 Stainless Steel Choose from 4 diameters Hard to find long lengths Length is measured from under head to tip of screw Be sure to use anti-seize compound or lubricant like WD-40 to prevent thread seizing.
$0.34 - $18.50
You have seen 48 out of 62 products
