Joist Hangers

Made in the USA with Type 316 (low Carbon) Stainless Steel 316 stainless provides the highest salt water corrosion resistance of the 316 types. Appropriate for marine and seaside applications and in other severe conditions where corrosion is a concern  Must be installed with specified stainless steel fasteners Patented double shear nailing distributes the load through 2 points on each joist for greater strength. The nails slant through the joist into the header, not only fastening the hanger but also helping to carry some of the load. The hanger design allows for the use of fewer fasteners for faster installation Install with specified stainless steel fasteners Full length 3” or 3-1/2” hand drive nails (or 2-1/2” collated connector nails) are always required for the patented double sheer (angled) nailing. Under some conditions alternative sized fasteners may be substituted but at a potentially significant load reduction. See nail substitution chart. LUS series hangers are not intended for welded applications Caution! - Do not bend or remove tabs or alter hanger in any way

Read more less

Made in the USA with Type 316 (low Carbon) Stainless Steel 316 stainless provides the highest salt water corrosion resistance of the 316 types. Appropriate for marine and seaside applications and in other severe conditions where corrosion is a concern  Must be installed with specified stainless steel fasteners Patented double shear nailing distributes the load through 2 points on each joist for greater strength. The nails slant through the joist into the header, not only fastening the hanger but also helping to carry some of the load. The hanger design allows for the use of fewer fasteners for faster installation Install with specified stainless steel fasteners Full length 3” or 3-1/2” hand drive nails (or 2-1/2” collated connector nails) are always required for the patented double sheer (angled) nailing. Under some conditions alternative sized fasteners may be substituted but at a potentially significant load reduction. See nail substitution chart. LUS series hangers are not intended for welded applications Caution! - Do not bend or remove tabs or alter hanger in any way

Read more less

Made in the USA with Type 316 (low Carbon) Stainless Steel 316 stainless provides the highest salt water corrosion resistance of the 316 types. Appropriate for marine and seaside applications and in other severe conditions where corrosion is a concern  Must be installed with specified stainless steel fasteners Patented double shear nailing distributes the load through 2 points on each joist for greater strength. The nails slant through the joist into the header, not only fastening the hanger but also helping to carry some of the load. The hanger design allows for the use of fewer fasteners for faster installation Install with specified stainless steel fasteners Full length 3” or 3-1/2” hand drive nails (or 2-1/2” collated connector nails) are always required for the patented double sheer (angled) nailing. Under some conditions alternative sized fasteners may be substituted but at a potentially significant load reduction. See nail substitution chart. LUS series hangers are not intended for welded applications Caution! - Do not bend or remove tabs or alter hanger in any way

Read more less

Made in the USA with Type 316 (low Carbon) Stainless Steel 316 stainless provides the highest salt water corrosion resistance of the 316 types. Appropriate for marine and seaside applications and in other severe conditions where corrosion is a concern  Must be installed with specified stainless steel fasteners Patented double shear nailing distributes the load through 2 points on each joist for greater strength. The nails slant through the joist into the header, not only fastening the hanger but also helping to carry some of the load. The hanger design allows for the use of fewer fasteners for faster installation Install with specified stainless steel fasteners Full length 3” or 3-1/2” hand drive nails (or 2-1/2” collated connector nails) are always required for the patented double sheer (angled) nailing. Under some conditions alternative sized fasteners may be substituted but at a potentially significant load reduction. See nail substitution chart. LUS series hangers are not intended for welded applications Caution! - Do not bend or remove tabs or alter hanger in any way

Read more less

Made in the USA with Type 316 (low Carbon) Stainless Steel 316 stainless provides the highest salt water corrosion resistance of the 316 types. Appropriate for marine and seaside applications and in other severe conditions where corrosion is a concern  Must be installed with specified stainless steel fasteners Patented double shear nailing distributes the load through 2 points on each joist for greater strength. The nails slant through the joist into the header, not only fastening the hanger but also helping to carry some of the load. The hanger design allows for the use of fewer fasteners for faster installation Install with specified stainless steel fasteners Full length 3” or 3-1/2” hand drive nails (or 2-1/2” collated connector nails) are always required for the patented double sheer (angled) nailing. Under some conditions alternative sized fasteners may be substituted but at a potentially significant load reduction. See nail substitution chart. LUS series hangers are not intended for welded applications Caution! - Do not bend or remove tabs or alter hanger in any way

Read more less

Made in the USA with Type 316 (low Carbon) Stainless Steel 316 stainless provides the highest salt water corrosion resistance of the 316 types. Appropriate for marine and seaside applications and in other severe conditions where corrosion is a concern  Must be installed with specified stainless steel fasteners Patented double shear nailing distributes the load through 2 points on each joist for greater strength. The nails slant through the joist into the header, not only fastening the hanger but also helping to carry some of the load. The hanger design allows for the use of fewer fasteners for faster installation Install with specified stainless steel fasteners Full length 3” or 3-1/2” hand drive nails (or 2-1/2” collated connector nails) are always required for the patented double sheer (angled) nailing. Under some conditions alternative sized fasteners may be substituted but at a potentially significant load reduction. See nail substitution chart. LUS series hangers are not intended for welded applications Caution! - Do not bend or remove tabs or alter hanger in any way

Read more less

Ideal for sight exposed connections and end of ledger/rim joist installations Made in the USA Type 316 Stainless Steel for ultimate corrosion resistance Install with specified stainless steel fasteners Under certain conditions, alternative size nails or Simpson SD screws may be substituted. Note that it may significantly alter load capacity. See the nail substitution chart. Caution! - Do not bend or remove tabs or alter hanger in any way

Read more less

Ideal for sight exposed connections and end of ledger/rim joist installations Made in the USA Type 316 Stainless Steel for ultimate corrosion resistance Install with specified stainless steel fasteners Under certain conditions, alternative size nails or Simpson SD screws may be substituted. Note that it may significantly alter load capacity. See the nail substitution chart. Caution! - Do not bend or remove tabs or alter hanger in any way

Read more less

Ideal for sight exposed connections and end of ledger/rim joist installations Made in the USA Type 316 Stainless Steel for ultimate corrosion resistance Install with specified stainless steel fasteners Under certain conditions, alternative size nails or Simpson SD screws may be substituted. Note that it may significantly alter load capacity. See the nail substitution chart. Caution! - Do not bend or remove tabs or alter hanger in any way

Read more less

Ideal for sight exposed connections and end of ledger/rim joist installations Made in the USA Type 316 Stainless Steel for ultimate corrosion resistance Install with specified stainless steel fasteners Under certain conditions, alternative size nails or Simpson SD screws may be substituted. Note that it may significantly alter load capacity. See the nail substitution chart. Caution! - Do not bend or remove tabs or alter hanger in any way

Read more less

The SU series of hangers are skewed 45° left or right. Angled nail slots direct nails for proper placement. These hangers will normally accommodate a 40° - 50° skew. The letter "L" in the code designates left skew. The letter "R" designates right skew. Made in the USA Type 316 Stainless Steel for ultimate corrosion resistance Features several configurations for wind and seismic resistance ties for trusses and rafters. Install with specified stainless steel fasteners

Read more less

The SU series of hangers are skewed 45° left or right. Angled nail slots direct nails for proper placement. These hangers will normally accommodate a 40° - 50° skew. The letter "L" in the code designates left skew. The letter "R" designates right skew. Made in the USA Type 316 Stainless Steel for ultimate corrosion resistance Features several configurations for wind and seismic resistance ties for trusses and rafters. Install with specified stainless steel fasteners

Read more less

The SU series of hangers are skewed 45° left or right. Angled nail slots direct nails for proper placement. These hangers will normally accommodate a 40° - 50° skew. The letter "L" in the code designates left skew. The letter "R" designates right skew. Made in the USA Type 316 Stainless Steel for ultimate corrosion resistance Features several configurations for wind and seismic resistance ties for trusses and rafters. Install with specified stainless steel fasteners

Read more less

The SU series of hangers are skewed 45° left or right. Angled nail slots direct nails for proper placement. These hangers will normally accommodate a 40° - 50° skew. The letter "L" in the code designates left skew. The letter "R" designates right skew. Made in the USA Type 316 Stainless Steel for ultimate corrosion resistance Features several configurations for wind and seismic resistance ties for trusses and rafters. Install with specified stainless steel fasteners

Read more less

The SU series of hangers are skewed 45° left or right. Angled nail slots direct nails for proper placement. These hangers will normally accommodate a 40° - 50° skew. The letter "L" in the code designates left skew. The letter "R" designates right skew. Made in the USA Type 316 Stainless Steel for ultimate corrosion resistance Features several configurations for wind and seismic resistance ties for trusses and rafters. Install with specified stainless steel fasteners

Read more less

The SU series of hangers are skewed 45° left or right. Angled nail slots direct nails for proper placement. These hangers will normally accommodate a 40° - 50° skew. The letter "L" in the code designates left skew. The letter "R" designates right skew. Made in the USA Type 316 Stainless Steel for ultimate corrosion resistance Features several configurations for wind and seismic resistance ties for trusses and rafters. Install with specified stainless steel fasteners

Read more less