Deck Essentials

Semi-Transparent formula enhances the natural beauty & grain of your hardwoods while maintaining the wood's natural beauty Perfect for all exterior wood surfaces including decking, fences & railings Provides protection from water, mold, mildew and damaging UV rays Exceptional penetration in even the densest of hardwoods with minimal raising of the grain For use with Ipe, Cumaru, Tigerwood & other exotic hardwoods Low 250 g/l VOC Formula See Videos Tab for Application DemoDownload Ipe Oil Application Instructions Ships by UPS Ground Only, No Airs. Cannot ship to Alaska or Hawaii or Cities in California's South Coast AQMD area ✔ Exceptional penetration in even the densest of hardwoods with minimal raising of the grain ✔ Perfect for all exterior wood surfaces including decking, fences & railings ✔ Reduces chance of warping & cracking ✔ Contains "Transoxide", slightly tinted pigments for UV defense ✔ Low VOC formula Coverage:Smooth Wood 250 to 300 square feet per gallonRough Wood 150 to 250 square feet per gallonIpe and other exterior hardwoods naturally vary in color. Deckwise Ipe & hardwood oil brings out the natural colors and beauty of the wood. Ipe may be of varying color depending upon the tree it was harvested from. Some exhibit more red, yellow or brown tones. No hardwood project will ever look exactly the same.

Read more less

Self-sealing, waterproof flashing Self-seals around fasteners to insulate deck joists from water and prevent wood rot and decay Butyl tape can be installed in cooler temperatures, safe to use in temps as low as 25° F. Can be applied to decking joists, over ledger boards, and around support posts to create a waterproof seal. Tear resistant, durable and flexible. Can be applied to dewy or non-kiln dried wood. However, it is always preferable to apply to clean, dry wood. Available in 2 sizes, see photos for the difference in width. Made in the USA!

Read more less

Deckwise has created a 2 part cleaner and brightener system for hardwood decks, rails, fences and all exterior wood surfaces. Part 1 is the cleaner, designed to remove dirt and natural graying from the wood. The cleaner contains Sodium Percarbonate to break down mold and mildew. Part one restores your hardwood's color and grain pattern Follow with Part 2, the brightener. This is designed to renew the color by removing tannin stains as well as those caused by, rust, fungus, and any dirt remnants. Active ingredient Oxalic Acid helps to neutralize pH of the wood after cleaning. This process allows for even absorption of stain or oil and increases it's longevity! Used together the cleaner and brightener will remove stains and graying and prepare the wood for Ipe Oil, a hardwood deck finish or Wisecoat, a water-based sealent to protect and bring out the wood's natural color.

Read more less

Self-sealing, waterproof flashing Self-seals around fasteners to insulate deck joists from water and prevent wood rot and decay Butyl tape can be installed in cooler temperatures, safe to use in temps as low as 25° F. Can be applied to decking joists, over ledger boards, and around support posts to create a waterproof seal. Tear resistant, durable and flexible. Can be applied to dewy or non-kiln dried wood. However, it is always preferable to apply to clean, dry wood. Available in 2 sizes, see photos for the difference in width. Made in the USA!

Read more less

12" x 25' ft Roll For Ledger Boards & Deck Posts DeckWise® Ledger Tape is a malleable polyethylene waterproof wood flashing material using a rubberized asphalt mastic adhesive. ✔ Durable, self-adhesive flashing. Protects deck ledger boards against water ✔ When applied over ledger boards, it creates a waterproof barrier that trains water to move over and away from the board. ✔ Wrap in-ground wooden deck posts to provide a barrier against fungi and soil moisture! ✔ Self seals around fasteners preventing moisture from penetrating the barrier. ✔ Made in the USA

Read more less

The popular Ipe Seal® Hardwood End Grain Sealer is now available in a user-friendly 16oz container! Apply with ease with the brush top, nothing else required for application! Container covers approximately 250 sq ft of decking. Ipe Seal wax emulsion sealant is used once on freshly cut lumber to seal and protect structural integrity. Prevents end checking or splitting on the edges of your brand new deck boards. Application recommended within 24 hrs of cutting the wood

Read more less

Deck & Wood Cleaner Part 1, 16 oz Cleans outdoor/exterior wood by removing dirt & natural graying in preparation for oiling or finish staining. Cleaning and brightening is recommended at least once a year for maintenance and restoration Perfect for preparing deck boards for Ipe Oil™ Hardwood Deck Finish Biodegradable

Read more less

Deck & Wood Brightener Part 2 Removes tannin stains from woods susceptible to extractive bleeding, such as cedar & redwood Active ingredient Oxalic Acid helps to neutralize pH of the wood after cleaning. This process allows for even absorption of stain or oil and increases it's longevity! Perfect for preparing deck boards for Ipe Oil™ Hardwood Deck Finish Brightener also removes rust and fungi stains while evening out the color across board. No more discoloration! Cleaning and brightening is recommended at least once a year for maintenance and restoration

Read more less

Color-Coded Deck Board Spacers Quickly & accurately provides uniform spacing of deck boards Versatile design allows use in any position between deck boards Special design prevents denting or marring of hardwood or composite boards Re-Usable - Made in the USA

Read more less

New Water-Based Sealer! Deck End Grain Sealer Appropriate for use with hardwoods, thermally modified wood, soft woods, pressure treated and composites Best if applied within 24 hrs of wood cutting Application creates a flexible, breathable barrier, providing enhanced protection Helps to resist warping and cupping while also inhibiting rot and decay Paintable and stainable in 24hrs after drying Great for decking, siding, cladding, steps and more! Non-toxic, eco-friendly formula

Read more less

Ipe Seal® creates a bond that extends the life of each deck board by preventing end checking & splitting Wax emulsion sealant protects the end cuts on hardwood decking Coverage is approximately 500 square feet per quart It is recommended to apply sealer to the exposed end grain within 24hrs of cutting the wood

Read more less

Hardwood Deck, Siding & Fence Sealer - 1 Gallon Use to waterproof and seal hardwood decking Low VOC, non-toxic formula Prevents cupping and warping Covers approx. 250-350 sq. ft/ gallon per coat Protects against mildew, mold and harmful UV rays Odorless and non-flammable Safe to use around people, pets and plants. Eco-friendly Guaranteed to prevent excess water accumulation below wood surface for up to 6 years! Product uses a water based tint that enhances the natural wood grain. Test before applying over entire surface.

Read more less

The PRO PLUG™ Glue Nozzle is to be used with the Pro Plug System for Wood. The nozzle coats the sides of the plug hole for maximum holding power. Little or no glue is deposited on the bottom of the hole. This prevents excess glue deposits from forming a hydraulic lock that makes plug insertion impossible.

Read more less

The 2 piece Pro Plug Fascia Plug Tool set is used to install the Pro Plug System for Trex Fascia.Included in the set: Fascia Plug Pre-drilling Tool PVC/Composite Tool ( Screw Depth Setter) The blue Fascia Plug Tool pre-drills the hole for the Trex fascia plugs. It leaves just enough width for the plug to fit snuggly while also allowing for natural expansion and contraction of the fascia board.The PVC Composite tool is then used to drive the screw to the correct depth. This tool features a No Cam-Out Auto-Stop mechanism that installs the screw correctly each time and prevents the screw from stripping. Install screws using the purple trim bit- included in both the kit and the tool pack.

Read more less

SMART-BIT® Deck Screw Depth Setter is designed to make fastening decks easier & faster with clean and uniform results - Perfectly Set Screws...Every Time. Auto-Stop Once target depth is reached, the Auto-Stop™ mechanism inside the tool disengages the driver bit and stops the screw from driving without further stripping the screw recess Locking Ring Secures the depth of the tool for consistent screw depth every time Adjustment Ring Depth can be adjusted for many different types and sizes of screws & applications Works well with Cap-Tor XD screws for composite decks Not for use with an impact driver See additional information below for instructions for use This amazing tool will set your screws to the same adjustable depth each and every time. Once target depth is reached, the Auto-Stop mechanism inside the tool disengages the driver bit and stops the screw from driving further - without stripping the screw recess or damaging the deck surface. Note from the manufacturer, Starborn Industries:Instructions for UseGeneral UseLoosen Locking Ring (2) and set fastener depth by moving the Adjustment Ring (3) to the desired position. The adjustment ring must engage at least two full threads of the tool body. Secure the Adjustment Ring with the Locking Ring (2). To determine the desired screw depth, practice on scrap material.Drill in a straight and stable fashion with a standard drill*. The screw is set when the Auto-Stop™ mechanism engages fully. In most decking materials, the tool makes a clear popping sound when the Auto-Stop™ engages.Replacing Driver BitDisconnect power and retract tool fully; remove bit with pliers. To insert new bit, retract tool fully and insert bit all the way into tool.*Note: Impact drivers may not set screws to the correct depth and may cause the locking ring to come loose. Standard drills are recommended for use with the Smart-Bit Depth Setter.Works with Torx® and Phillips® BitsEach tool includes one T-20 bit in the tool and four additional replacement bits ( (2) T-20 bits, (1) T-25 and (1) #2 Phillips bit

Read more less

Includes: (1) Pro Plug Tool for Wood (1) Pack of 5 replacement bits (1) bottle of wood glue (brand may vary) (2) pieces of 5" orbital sand paper - 60 grit (3) T20 star drive bits

Read more less

Creates a perfect hole & depth every time! Fascia System allows for the expansion & contraction of fascia boards For use with Deckfast Fascia System Screws No Cam-Out Auto-Stop mechanism prevents screw recess stripping Free Spinning Stop Collar protects the fascia surface Rubber O-ring prevents damage to the work surface once the target depth is reached Fascia Tool Features ✔ Free Spinning Stop Collar with O-Ring: The stop collar spins free of the drill bit, prevent marring or burnishing of the fascia board surface. ✔ Anti-clog Debris Cavity: The cavity gathers waste material, keeping it clear of the countersink. ✔ Pre-set Countersink: The Fascia Tool matches the head diameter and countersink depth of the Fascia Screw for the perfect hole and fit. ✔ Pre-set Shaft length: Together with the countersink, the overall hole depth is designed for use with fascia boards from 1/2" to 3/4" thick.

Read more less

4 pack of replacement bits for the Pro Plug Tool for PVC. Choose between deck and trim bits replacements.

Read more less

Replacement bit pack for the Pro Plug Tool for Wood. Includes 5 replacement drill bits Creates a 1-1/2" (38mm) hole To be used with the Pro Plug System for Wood

Read more less

With Replaceable Powerbolic™ Drill Bits. Available in 5 sizes. Save with the Combo Kit. Pre-drill and countersink in one fast step with the new Smart- Bit® Smart-Bit® removes the guesswork from pre-drilling and countersinking Smart-Bit Quickly drills the perfectly countersunk hole in deck boards Drills a 1-1/8" deep hole (including countersink)sufficient for decking up to 5/4" nominal thickness Excellent for use in hardwoods and composite lumber, eliminating "mushrooming" around the screw head in composites

Read more less