Fastening & Anchoring

Titen HD® is made from Type 316 Stainless Steel with carbon-steel lead-threads Perfect for concrete and masonry where corrosion is a concern. Serrated carbon-steel threads at the tip cut concrete and allow remaining threads to interlock with the concrete. Contains less than 1% carbon steel to minimize expansion compared to 18% found in other stainless screw anchors. Unlike other anchors, the Titen HD® will not cause concrete failure due to rust. See design info PDF in the specs section below. Install by hand or with an impact wrench. See PDF in spec section for installation information

Read more less

Type 316 Stainless Steel Annular Thread, flat head Made of type 316 stainless steel for the ultimate corrosion resistance For installation of stainless steel joist hangers & framing connectors Made in USA AISI Grade 316 Stainless Steel has lower carbon content than 305 or 302HQ and contains molybdenum for superior corrosion resistance in salt water and other highly corrosive environments. It is the grade of stainless steel to be specified in any seaside application.

Read more less

Type 410 Stainless Steel for enhanced corrosion protectionAvailable in Hex and Phillips Flat Head, 100pc BoxIdeal for attaching components like light fixtures or electrical boxes to concrete and masonryGreat for concrete, brick, grout-filled CMU and hollow-block applicationsSuitable for some preservative-treaded wood applicationsDrill Bits included in each box

Read more less

The Construction screw does the job of a lag screw. Dome Head enhances the structural capability. Tapper Point which consists of the Cork Screw Start and Blade Cutting Thread for easy piercing and alleviating strain on the material. Specially designed Tight Star Recess system holds U2 bits firmly in place allowing these screws to be installed with one hand. "Talon Grip" nibs under the head hold the screw tight to prevent loosening and dig into the material when countersunk. Reamer Thread enlarges the hole in the material to create a larger passage when drawing materials together and reduces tension on the screw head. ***This thread is not on the 1/4" x 2" screw

Read more less

Heavy-Duty structural screw Marine Grade 316 for the ultimate corrosion resistance Heavy-duty diameter, SawTooth™ point and flat washer head Easy to install - saves time and lowers installation cost Perfect for docks, wharves, piers, boardwalks and more! Use when strength and corrosion resistance are critical. Easy to back out and reinstall as needed Driver bit included in each box Installs 5x faster than a traditional Lag Screw! No predrilling or counterboaring required.

Read more less

The Titen HD® now with countersunk head style!This high-strength screw anchor is perfect for use in cracked and uncracked concrete as well as masonry. Conveniently sold by the piece! Type 316 Stainless Steel provides long-lasting corrosion resistance. Cracked concrete code listed Provides industry leading Countersunk head leaves a flush-mount profile and clean surface appearance for exposed through-set applications performance even in seismic and wind loading conditions Installs using a standard-sized ANSI tolerance drill bit - The 3/8" Titen takes a T-50 bit, sold separately here. Removable. Great for temporary anchoring See spec table for installation pdf

Read more less

Type 316 Stainless Steel for ultimate corrosion resistance 1/4” diameter high-strength structural wood screw 3/8” hex head with 0.48” integrated washer Type-17 point enables easy driving with no pre-drilling and minimal wood splitting Used to fasten certain heavy duty framing connectors to wood members Excellent for fastening ledger boards 25pc box

Read more less

The Strong-Drive SD Connector screw is designed for use in stainless steel connectors, replacing the need for nails. Load Rated Tested and approved for use with many Simpson Hangers and Connectors In certain applications, the load values achieved by the #9 SD Screw is greater than that of 10d common nails Specially designed screw shank pairs with holes in Simpson Connector Box includes the hex driver

Read more less

Full Round Head, Paper Tape Collated- Type 316 Stainless Steel Sold in convenient job packs Ring Shank Approved for use in ACQ lumber Commonly Used Tools for Installation Bostitch: 533PT F33PT MCN150 MCN250Hitachi: NR65AK NR65AKSPaslode: 5250/65SS-PP PF150S-PP F250S-PPSenco: HN150 HN250

Read more less

Type 316 Stainless Steel for ultimate corrosion resistance Code listed for cracked concrete and uncracked concrete See code listings Head stamped with length identification number Chamfered top to prevent mushrooming during installation Optimal choice for performance under seismic and high-wind conditions Qualified for a minimum 3-1/4” concrete thickness Tested per ACI355.2 and AC193 specifications concrete design information available in spec section below

Read more less

The U2 Fasteners Black Flat Head Screw combines versatility and style.  Great for use in deck frames, fencing, ledger boards, posts, and professional timber construction. Flat Head with Talon Grip.  Allows for increased pull-through resistance. Tapper Point enables easy piercing and reduced strain on material while installing. Tight Star Recess system is designed to hold U2 bits firmly in place.  They won't slip, even when upside down, allowing these screws to be installed with one hand.   Screw coating is CR3 free base finished with a black nano coating.  It protects against corrosion, wear, and friction ensuring long lasting protection 

Read more less

The Construction screw does the job of a lag screw.  This code-compliant heavy-duty self-tapping structural fastener is versatile and great for a variety of uses. Dome Head provides an extra-large bearing surface under the head. Tapper Point enables easy piercing and relives strain on material while installing. Tight Star Recess system is specially designed to hold U2 bits firmly in place.  They won't slip, even when upside down, allowing these screws to be installed with one hand.   Talon Grip nibs secure screw fastening to prevent loosening over time.  Reamer Thread enlarges the hole in the material to create a larger passage when drawing materials together and reduces tension on the screw head. The perfect fastener for staircases, deck frames, ledger boards, joists, rafters, planters, play sets and more. 

Read more less

The Construction screw does the job of a lag screw.  This code-compliant heavy-duty self-tapping structural fastener is versatile and great for a variety of uses. Dome Head provides an extra-large bearing surface under the head. Tapper Point enables easy piercing and relives strain on material while installing. Tight Star Recess system is specially designed to hold U2 bits firmly in place.  They won't slip, even when upside down, allowing these screws to be installed with one hand.   Talon Grip nibs secure screw fastening to prevent loosening over time.  Reamer Thread enlarges the hole in the material to create a larger passage when drawing materials together and reduces tension on the screw head. The perfect fastener for staircases, deck frames, ledger boards, joists, rafters, planters, play sets and more. 

Read more less

Unique box thread reduces driving torque Hex Washer Head Type 316 Stainless Steel for maximum corrosion protection No pre-drilling is required for most applications Designed for structural wood to wood and engineered to wood connections. Ideal for ledgers

Read more less

The WEDGE-ALL® wedge anchors are a non-bottom bearing, wedge style expansion anchor for use in solid concrete or grout filled masonry.One-piece, wrap-around clip ensures uniform holding capacityThreaded end is chamfered for ease of starting nutOne piece wrap around clipSupplied with a nut and washerThreaded end is chamfered for ease of starting nutThreaded studs are set by tightening the nut Discontinued product, limited quantities available

Read more less